Lancom LW-600 ձեռնարկ

Lancom LW-600
7.5 · 1
PDF ձեռնարկ
 · 1 էջ
Անգլերեն
ձեռնարկLancom LW-600

LANCOM LW-500 / LW-600

Mounting instructions

MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS

Preparation for ceiling- or wall mounting
Use the mounting plate as a drilling template to mark
out the drill holes. Depending on the surface material the
required size of the holes may vary. If required, drill a hole
into the ceiling board to feed- through the connector cables.
Alternatively, you can use the integrated cable duct on the
access point to lead the cables sideways.
Mounting to other surfaces
For mounting the device to other surfaces than described
here, you may need different mounting accessories (screws,
dowels, etc.). Pre-drilling may not be necessary when using
the included self-drilling screws.
Mounting the access point
Ceiling mounting to a wooden ceiling
Included:
1 mounting plate (A), 2 screws 2.6*31 mm (B),
2 screws 2.6*5.2/6.3 mm (C)
Place the mounting plate A to a ceiling in your desired
location, insert the screws B through the appropriate holes,
and tighten the screws to fix the plate in place.
When the mounting plate is in place, insert the screws C
into the appropriate holes of the access point D.
Place the access point on the ceiling mounting plate by
inserting the attached screws C into the appropriate holes
of the mounting plate. Then twist the access point D clock-
wise until it clicks into place.
Mounting to a drywall ceiling
Included:
1 mounting plate (A), 2 self-drilling screws 40 mm (E),
2 screws 3.6*31 mm (B), 2 screws 2.6*5.2/6.3 mm (C)
Screw the self-drilling screws E to the ceiling at the previ-
ously marked positions. Screw as tight as possible until the
screw heads are flush-mounted to the ceiling to make it
possible to place the mounting plate A flat to the ceiling
surface in the next step.
Now align the mounting plate A with its appropriate holes
to the previously mounted self-drilling screws E, so that the
screws B can be screwed through the holes in the moun-
ting plate into the screw heads of the self-drilling screws
E. Tighten the screws B until the mounting plate rests
backlash-free on the mounting surface.
When the mounting plate is in place, insert the screws C
into the appropriate holes of the access point D.
Place the access point on the mounting plate by inserting
the attached screws C into the appropriate holes of the
mounting plate. Then twist the access point D clockwise
until it clicks into place.
14
A
B
C
D
B
C
A
B
C
D
B
C
E
E

MOUNTING INSTRUCTIONS

T-rail mounting
Included:
4 thread screws (2 pcs. 2.6*10 mm, 2 pcs. 2.6*25 mm (F),
4 T-rail brackets (2 pcs. 15.5 mm, 2 pcs. 24.9 mm (G),
2 spacers (H)
Select the correct size of T-rail brackets G from the two
sizes which are included in the package contents.
Attach the T-Rail brackets G to the appropriate holes in
the access point using the short screws F as shown. If you
need more space between the access point and the T-Rail,
then additionally use the spacers H between the brackets
and the holes, and use the longer screws F included in the
package contents.
Clip the access point D on to your T-Rail using the previ-
ously attached T-Rail bracket.
Wall mounting with mounting plate
Included (as listed in chapter Mounting to a drywall
ceiling):
1 mounting plate (A), 2 self-drilling screws 40 mm (E),
2 screws 3.6*31 mm (B), 2 screws 2.6*5.2/6.3 mm (C)
Fixing the mounting plate to the wall
Place the mounting plate A to a wall in your desired loca-
tion and rotate the plate to make sure that the end points 1
of the locking mechanism for fastening the access point are
horizontally aligned. In this position, use the mounting plate
as a drilling template to mark the position of the two holes
2. After having drilled the holes, use either the screws B, B
and E (as described in chapter Mounting to a drywall cei-
ling), or your own mounting material to fix the mounting
plate to the wall, depending on the wall material.
Preparing the access point
Insert the screws C into the appropriate holes of the access
point D.
Fixing the access point to the mounting plate
Place the access point on the mounting plate by inserting
the attached screws C into the appropriate holes 3 of the
mounting plate.
Then twist the access point clockwise (4) until it clicks into
place.
The screws C are now locked in their end positions 5 and
the access point is fixed to the mounting plate.

MOUNTING INSTRUCTIONS

A
B
C
D
B
C
D
D
3
3
4
4
5
5
D
G
F
(H)
G
F
(H)
D
1
1
2
2
A
5
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document
contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111934/0220

Ձեռնարկ

Դիտեք Lancom LW-600-ի ձեռնարկը այստեղ, անվճար: Այս ձեռնարկը մտնում է Մուտքի կետեր կատեգորիայի ներքո և գնահատվել է 1 մարդկանց կողմից, միջինը 7.5-ով։ Այս ձեռնարկը հասանելի է հետևյալ լեզուներով՝ Անգլերեն։ Lancom LW-600-ի վերաբերյալ հարց կամ օգնության կարիք ունե՞ք։ Ձեր հարցը տվեք այստեղ

Օգնության կարի՞ք ունեք։

Հարց ունե՞ք Lancom LW-600-ի մասին և չեք գտել պատասխանը ուղեցույցում։ Ձեր հարցը տվեք այստեղ: Նկարագրեք խնդիրը և ձեր հարցը հստակ և համապարփակ ձևով: Որքան մանրամասն լինի խնդրի կամ հարցի նկարագրությունը, այնքան ավելի հեշտ կլինի Lancom LW-600-ի մյուս օգտատերերի համար տալ ձեզ սպառիչ պատասխան:

Հարցերի քանակը. 0

Lancom LW-600-ի տեխնիկական պայմաններ

Ստորև դուք կգտնեք Lancom LW-600 արտադրանքի տեխնիկական բնութագրերը և ուղեցույցի բնութագրերը:

Ընդհանուր
Ապրանքանիշ Lancom
Մոդել LW-600
Ապրանք Մուտքի կետ
EAN 4044144618291
Լեզու Անգլերեն
Ֆայլի տեսակ Օգտագործողի ձեռնարկ (PDF)
Features
2.4 GHz
5 GHz
Maximum data transfer rate 1775 Mbit/s
Maximum data transfer rate (2.4 GHz) 575 Mbit/s
Maximum data transfer rate (5 GHz) 1200 Mbit/s
Channels quantity 19 channels
Number of users 128 user(s)
Networking standards IEEE 802.11a,IEEE 802.11ac,IEEE 802.11ax,IEEE 802.11b,IEEE 802.11d,IEEE 802.11g,IEEE 802.11h,IEEE 802.11i,IEEE 802.11v,IEEE 802.1x
MIMO
MIMO type Multi User MIMO
Channel bandwidth 40 MHz
Maximal-Ratio Combining (MRC)
Short Guard Interval (GI) Yes
Band steering
VLAN support
Number of VLAN IDs 4096
Quality of Service (QoS) support
Security
Number of SSID supported 16
Security algorithms AES-CCMP,AES-GCMP,EAP-FAST,EAP-GTC,EAP-TLS,EAP-TTLS,MSCHAPv2,PEAP,TKIP,WEP,WPA2-Enterprise,WPA3
Power
Power over Ethernet (PoE)
AC input voltage 230 V
Output voltage 12 V
Output current 1 A
Power consumption (typical) 11.04 W
Ports & interfaces
Ethernet LAN (RJ-45) ports 1
USB 2.0 ports quantity 0
DC-in jack
Antenna
Antenna type Internal
Antennas quantity 2
Operational conditions
Operating relative humidity (H-H) 0 - 90 %
Operating temperature (T-T) 0 - 40 °C
Weight & dimensions
Width 177.7 mm
Depth 177.7 mm
Height 37.7 mm
Design
Placement Ceiling
Product colour White
Housing material Plastic
Certification EN 62368-1:2014+AC:2015+A11:2017, EN 62479:2010, EN 301 489-1 V2.1.1, EN 301 489-17 V3.1.1, EN 300 328 V2.2.2, EN 301\n893 V2.1.1
Packaging data
Number of products included 1 pc(s)
AC adapter included
Cables included LAN (RJ-45)
Mounting kit
Quick start guide
PoE adapter included
Management features
Web-based management
Firmware upgradeable
ցույց տալ ավելին

Հաճախակի տրվող հարցեր

Չե՞ք կարող գտնել ձեր հարցի պատասխանը ուղեցույցում: Ձեր հարցի պատասխանը Lancom LW-600-ի մասին կարող եք գտնել ստորև ՀՏՀ բաժնում:

Ձեր հարցը նշվա՞ծ չէ: Ձեր հարցը տվեք այստեղ

Արդյունքներ չկան